『DE』3 Axis NEMA23 Stepper Motor 425oz-in 112mm& Driver&USBCNC Controller CNC Kit

EUR 258,23 Sofort-Kaufen, EUR 21,42 Versand, eBay-Käuferschutz
Verkäufer: powace08 ✉️ (4.091) 99.3%, Artikelstandort: Frankfurt, DE, Versand nach: EUROPEAN_UNION, GB, Artikelnummer: 275224122041 『DE』3 Axis NEMA23 Stepper Motor 425oz-in 112mm& Driver&USBCNC Controller CNC Kit.         『DEU』3 Axis NEMA23 Stepper Motor 425Oz-in Dual Shaft&Driver&USBCNC Board CNC Kit For CNC Router Milling Engraving Machine

We will Ship from Germany warehouse to Below Europe Countries

Austria Belgium Bulgaria

Czech Republic

Croatia

Denmark Estonia
Finland France Germany Greece Hungary Ireland Italy
Latvia Lithuania Luxembourg Netherlands Poland Portugal Romania
Slovakia Slovenia Spain Sweden UK Malta  

Package include: 

  • 3 x 23HS2430B Nema23 Stepper Motor D ual Shaft ( 425oz-in,112mm Length ,3A )
  • 3 x FMD2740C stepper motor driver
  • 1 x 400W 36V 9.7A DC switching power supply
  • 1 x 4 Axis USB CNC breakout board
  • 1 x Hand controller
  • 1 x USB Cable
  • 1 x CD include the user manual,usbcnc software and registration key.

100% Brand New and High Quality!!!

This interface board is based on USBCNC MK1 and just use in our provide software and function, cannot support other versions of the software and function  

1.  4 Axis USBCNC breakout board

 

1) Products brief introduction 

USBCNCV4.0 is a high performance motion controller which based on PC software USBCNC control, the system can complete the conversion from G code to connect stepper motor’s driver motion control signal without requiring any additional hardware and software. This control card is compatible with most stepper driver and servo driver,it is a perfect controller that instead of parallel Mach3 interface board.

 

2) Computer system requirement        

Minimum configuration:

1) CPU:1GHz

2) Memory: 512MB

3) 500MB free disk space

4) DIRECTX9 graphics device with WDDM 1.0 or higher driver

5) USB 2.0 interface

6) Net FRAMEWORK 3.5SP1

 

The recommended configuration:

1) CPU:2GHz dikaryon

2) Memory: 2GB;

3) 1G free disk space

4) DIRECTX9 graphics device with WDDM 1.0 or higher driver

5) USB 2.0 interface

6) Net FRAMEWORK 3.5SP1

 

3.Production feature

  1. After the revision,V4 version using the red PCB board, PCB size is 135.3*82.5mm.;

2. The front of the narrow edge placed with USB communication interface and DB9 hand control interface for the convenience of customers drawn from the case panel directly;

3. The back-end of narrow edge is power input and output interface and 3 relay output interface; relay is strong interference source, relay away from the design of main control chip, it is conducive to the stability of the board;

4. One of the two wide sides is stepper motor and principal axiscontrol signal output;

5. The another side of two wide sides is the emergency stop, manual speed input, limiting input interface; one side for the input, another side output connection mode is simple and convenient;

6. 5V and 12V power module compact independence, security, stability;

7. External ensure the stability of the system work effectively with crystal active and main control chip shield;

8.outline dimension is 135.3*82.5mm, product positioning hole installment dimension is 127*75mm

9. The software is USBCNC,not mach3,pls note!

This item is easy to operate for DIY hobby user,but it is control by USB port,so need more careful for the software install,and pls must be strict read the user manual and follow us.

 

 

 

 

2. FMD2740C  stepper motor driver

1) Brief introduction

FMD2740C driver by Japanese sanyo's chip,After multiple optimize R & D and production of high-subdivision 2-phase stepper motor drives, suitable for driving small and medium-sized phase current is less than 4A 2-phase or 4-phase hybrid stepping motor. Due to the adoption of the new bipolar constant current chopper drive technology, using the same motor can output more speed and power than other drivers. Segments stepper motor running accuracy improved, reduces vibrations and noise reduction.

 

2 ) Features

1.  High-performance, low price        

2.  Bipolar constant current chopping mode

3.  Power supply voltage 12 to 40VDC          

4.  High-speed optocoupler signal isolation input

5.  20kHz chopping frequency             

6.  Subdivision precision  2\8\16\32\64\128\10\20  optional   

7.  Electrical input signal is TTL compatible

8.  Stationary current is automatically reduced by half

9.  Shape design is convenient for installation         

10. Maximum drive current is  4A

11. Drive any 4A phase current of 2-phase or 4-phase hybrid stepping motor                  

  3 )Applications

Suitable for a variety of small and medium-sized automation equipment and instruments,for example: Small engraving machine, SMT machine, etc.

 

4 ) Wiring defined

Weak signal interface  

Signal

Function

SP+

Pulse signal + end

SP-

Pulse signal - end

DIR+

Direction signal +end

DIR-

Direction signal-end

EN+

Enable signal +end

EN-

Enable signal -end

 

Strengths connection port

Signal

Function

VIN+

12to50 v dc power supply input +end ,it is recommended to use 36V3A

GND

DC power supply connection ground

A+

Stepper motor A + Phase terminal

A-

Stepper motor A - Phase terminal

B+

Stepper motor B+  Phase terminal

B-

Stepper motor B - Phase terminal

     

NOTE:    This drive does not contain anti-anti-interpolation circuit so non-input positive and negative power supply upside down! Otherwise it will damage the drive!  

 

5 ) The electrical characteristics

6) The use of the environment and parameters

Cooling method

Natural cooling or forced air cooling 

Use of the environment

Occasions

Avoid dust, oil mist and corrosive gases

Temperature

0 °C-+50 °C

Humidity

40-90%RH

Vibration

6m/s2 MAX

Storage temperature

-20 °C-+65 °C

Weight

250g

 

7 ) Mechanical installation size

8) Power supply

  

The supply voltage can work normally in between DC12V-50V, FMD2740C driver can use ordinary switch DC power supply, can also be used for transformer and the bridge rectifier and filter capacitor, capacitance desirable 2000U to 5000U. Note rectified voltage ripple crest does not exceed 50V.Recommended the user to use the 24V-32V DC supply , avoid the grid fluctuations over drive voltage operating range.

 

Note:

1, Wiring should pay attention to the power of positive and negative Do not be reversed;

2, In order to reduce costs, multiple drives can share a power supply. But it should improve the rated power and rated output current of the power and attention to cooling.

 

9 )Attenuation of the DIP switch settings

Decay mode

SW1

SW2

Slow decay

OFF

OFF

Mixed decay

ON

OFF

Fast decay

OFF

ON

 

  10 )Subdivision DIP switch settings

 

11 )Current DIP switch settings

 

12 ) Drive motor controller wiring diagram

13 )Electrical wiring

The FMD2740C driver can drive all current 4A 4-wire, 6-wire or 8-wire 2-phase / 4-phase motors, are detailed below 4-wire, 6-wire, 8 wire stepper motor connection:

 14 )Matching of the drive and motor

FMD2740C driver can drive the domestic and foreign manufacturers of 2-phase or 4-phase motor, in order to obtain the most satisfactory driving, you need to choose a reasonable supply voltage and current setting. Supply voltage determines the level of the high-speed performance of the motor, and the current set value determines the output torque of the motor.

 

Supply voltage selected

 

Generally speaking, the higher the supply voltage, the greater the torque motor at high speed, the more it can avoid the high speed out. But another aspect, the voltage is too high will lead to over-voltage protection, and can even damage the drive, but also in the high-pressure work, low speed vibrations.

 

The output current is set

For the same motor, the greater the current setting, the higher speed, the current motor and drive more heat. So under normal circumstances the current setting into a powered machine warm but not too hot long-term value.

Note: the current settings after you run the motor for 15-30 minutes, if the motor temperature is too high, you should reduce the current settings. If the motor current setting, the motor output torque is not enough to improve heat dissipation conditions to ensure that the motor and drive are not hot.

   

 

3. Stepper Motor

Technical Specifications

Part No.:   23HS2430B

Frame Size:     NEMA23

Step Angle:     1.8 degree

Current:          3.0A/phase

Resistance:     1.6 Ohm/phase

Inductance:     6.8 mH/phase

Holding torque:280N.cm/28kg-cm     425 oz-in

Rotor inertia:   800g-cm2

Number of wire leads: 4

Weight:          1.66 kg

Length:           112mm

General Specification:

Step angle accuracy:+ -  5%(full step,not load)

Resistance accuracy: + - 10%

Inductance accuracy:+ - 20%

Temperature rise: 80deg Max(rated current,2 phase on)

Ambient temperature ----------—20deg  ----  +50deg

Insulation resistance:100ohm  Min,500VDC

Insultion Strength--------500VAC for one minute

Datasheet(23HS2430B,Front shaft 8mm dia and 21mm length,back shaft 8mm dia and 11mm length,425 oz-in or 28kg.cm holding torque)

 

This product also has a single shaft for choice, the need to invite the message.

 

 

Wiring:

  Red:      A+

Green:   A-

Yellow:  B+

Blue:     B-

 

 

400W 36V 11A DC Switching power supply

Specification

  • Model: S-400W-36V
  • Output Current:11A
  • Output Voltage:36V
  • Output Frequency:85%
  • Output Power: 400W

It comes with built-in cooling fan

Connection instruction

  • L: Live wire
  • N: Negative wire
  • +V: DC power output “+”
  • -V: DC power output “-“
  • +V ADJ: output voltage regulation

Wiring diagram

 

 

5.Usage or Application

 

This products are widely used in engraving machine, printer, medical equipment,  embroidery machine, stage lighting, textile automation, printing,  packaging and other industries automation equipment. Shipping     Please open the package and check if there are some damages before sign, if there are some damages , please do not sign and contact us immediately     Items will be shipped within 1-2 days upon the receipt of payment. Problem&Feedback     Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it.     We are a new member in ebay now, and need understand both of sides     Pls email us before you want to leave any negative feedback Refund     When you have the parcel, and not satisfied the goods or it is other problem like as broken,pls tell us the detail reason and provide the photos     Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost Contact us     Welcome worldwide customer inquire and questions, we will try to do our best to feedback customer’s email within 1-2 business days,if not pls check the mail box again     Customer’s satisfaction is very important to us.
  • Condition: Neu
  • Holding torque: 425oz-in
  • Angebotspaket: Nein
  • Size: 57x57x112mm
  • Breakout board: 4 Axis USB CNC breakout board
  • Port: USB
  • Driver: FMD2740C
  • Power supply: 400W,36V/9.7A
  • Lieferumfang: Motor mit Treiber & Controller Board
  • Name: 3 Axis USB CNC Controller Kit
  • Ausländisches Produkt: Nein
  • Step Angle(degrees): 1.8
  • Marke: RATTM MOTOR
  • Anschlussbelegung: 4-Draht Zweipolig
  • Modifizierter Artikel: Nein
  • Stromart: Gleichstrom (DC)
  • Model: 23HS2430B/FMD2740C
  • Shaft: Dual shaft
  • Driver Microstep: 128 microstep
  • Vollschrittwinkel: 1.8° (200 Schritte)
  • Anschluss: USB

PicClick Insights - 『DE』3 Axis NEMA23 Stepper Motor 425oz-in 112mm& Driver&USBCNC Controller CNC Kit PicClick Exklusiv

  •  Popularität - 22 Beobachter, 0.0 neue Beobachter pro Tag, 739 days for sale on eBay. Super hohe beobachtend. 13 verkauft, 4 verfügbar.
  •  Bestpreis -
  •  Verkäufer - 4.091+ artikel verkauft. 0.7% negativ bewertungen. Großer Verkäufer mit sehr gutem positivem Rückgespräch und über 50 Bewertungen.

Die Leute Mochten Auch PicClick Exklusiv